Talk to Your Tank® — Get daily updates of your tank’s fill capacity
CylConnect® grants you peace of mind knowing exactly how much gas capacity is left in your tank or cylinder — without the need to physically check it until actual fill time.
Our telemetric devices provide daily updates to monitor and evaluate liquid level capacity, weight, or gas pressure parameters for your cryogenic tanks or HP cylinders — in urban as well as rural locations. Easily access all your tanks’ data in your CylConnect® online account or via the SMARTank mobile app (available for Android and Apple).
Benefits of CylConnect®
Know exactly how much product is left in your tank on a daily basis
Reduce your distribution costs up to 50%
Assures constant gas supply
Get out-of-stock forecasts ahead of time to avoid facing them
Catch leaky tanks before they cause a problem
Track rural areas without the need to visit locations until actual fill time
Types of tanks and vessels that can use CylConnect® Remote Monitoring
Small and large bulk tanks
Carbonation systems
Liquid cylinders
HP manifolds
Switch-overs
Plus, many custom solutions
How does CylConnect® work?
All you need is three components: (1) an uplink device, (2) appropriate sensor(s), and (3) the SmarTANK mobile app or computer to access your data!
Install the CylConnect’s uplink device onto your liquid cylinders and/or bulk tanks.
Connect the uplink device to the appropriate gauge (such as, the Level-Eye® liquid level gauge, a pressure gauge, or a differential pressure gauge).
CylConnect ST90 Uplink Device - How to Replace Battery Pack
Level-Eye Liquid Level Gauge
Replace Battery Pack
Replacing the ST90 Uplink Device Battery Pack
STEP 1: Remove old ST90 uplink device battery pack
To replace the ST90 uplink device battery pack, loosen screws on device cover and open lid.
Unhook white plastic battery connector (A) by pinching the lever and pulling upward.
Remove old battery pack from device housing and discard according to local EPA regulations.
STEP 2: Reset “Battery Life Counter” [IMPORTANT]
Before proceeding, you MUST reset the “Battery Life Counter” in your SMARTank account, otherwise battery life data will not read correctly in your account. NOTE: New battery pack must be DISCONNECTED for this step to work correctly. Do not connect white plastic battery connector until Step 3.
Reset “Battery Life Counter” in your SMARTank account:
A: Close lid and hold attached magnet (B) over “magnet symbol” (C) for five (5) seconds.
B. Or, push white START button (D) for five (5) seconds.
STEP 3: Install new battery pack & reactivate uplink device
Place new ST90 uplink device battery pack in housing.
Securely attach white plastic battery connector (A) until it clicks in place. (This action will automatically send a first “call.”)
Observe the two LED lights (E) on control board. GREEN light will flash slowly & then go out if first call is SUCCESSFUL.
– If first call is UNSUCCESSFUL, GREEN light will flash slowly, and RED light will illuminate and remain lit. Wait until both lights go out. Send another “call” by holding attached magnet (B) over LED area (E). Repeat action, if necessary.
Shut device cover and tighten screws until lid is seated flat to housing surface ensuring weatherproof protection of device.
STEP 4: Check your tank’s SMARTank data
Open your online SMARTank account and do the following tests:
– Compare data in your account with the tank’s actual gauges.
– Confirm battery level in account is reading “99%” (F) If tank data does not read within a 1-2% margin or the battery level is not reading 99%, send another call and check data again. Call Cyl-Tec for further assistance, if needed.
PDF Download Library
CylConnect Remote Monitoring
CylConnect ST90 Uplink Device - How to Replace Battery Pack
Level-Eye Liquid Level Gauge
CylConnect Devices
“SMARTank” ST90 UPLINK Device
U.S.: AT&T LTE or Verizon LTE
Mode: LTE Digital Wireless Radio with fallback to GSM/900MHz Wideband WLAN
Enclosure: NEMA 4X; weatherproof, UL Approved (UL94V-0); CPVC
GPS Receiver: Internal Antenna
LAN/WAN: Wideband 900MHz, 300 ft. Line of Sight
Accuracy: +/- 0.5% Full Scale of Range (BFST)
Operating Temperature: 13° to 158°F (-25° to 70°C)